Spring Fling Towel Hanger Supplies Needed: 1 Sheet Solvy WSS Thread Spray Adhesive White fabric Ribbon for creating loop at top Timtex, felt or heavy white fabric 10" strip of fabric Iron Pressing Cloth 2 Sheets Fabri-Solvy (available online and in some stores) Sources: http://www.sulky.com/stabilizers/fabrisolvy.php http://www.greatnotions.com/si_popup.asp?ItemID=32081 http://www.joann.com/joann/catalog/productdetail.jsp?CATID=cat1122&PRODID=prd38125 To Start: Cut a piece of 10 square Timtex Cut a piece of fabric 10x3 inches. FOld in half right sides together. Sew down long side with a 1/4 inch seam. Turn and press. Turn Timtex over. Center the completed strip and make sure that it is placed horizontally. Hand baste in place with a running stitch down the center. You can remove stitches when finished. See attached photo in your design set. 1. Hoop Fabri-Solvy, Fabric, WSS Solvy in that order. (Please do not omit the WSS solvy. It gives the design a crisp look.) 2. Sew out design up to the last two colors. 3. Stop. 4. Remove hoop from machine but DO NOT UNHOOP. 5. FLoat the Timtex or felt under the bottom afixing with spray adhesive. (MAKE SURE THE horizontally placed strip that you afixed by hand sewing IS FACE DOWN TO THE BACK. IT SHOULD SHOW WHEN COMPLETED.) 6. Return hoop to machine and continue sewing out the next to the last color. 7. Remove hoop again (DO NOT UNHOOP) 8. Turn Hoop over. Trim only Timtex or felt away close to stitching but not through it. BE SURE NOT TO CUT INTO THE Fabri Solvy. 9. Turn Hoop back over. On top trim WSS and fabric away close to stitching but not through it. BE SURE NOT TO CUT INTO THE Fabri Solvy. 9. Return hoop to machine and finish sewing last color. 10. Remove from hoop and trim design close to final stitch. 11. TO remove the excess Fabri Solvy use a warm water dampened sponge to run around the design. 12. Let finished towel topper dry well if damp. 13. Place between the pressing cloth and gently press. 14. Hand stitch a looped ribbon at the top of the towel topper. This will be your hanger. 15. Remove basting stitches from back of towel hanger. 16. You towel will drape through the horizontal strip on back. ------------------------------------------------------------------------------------------------------------------------- Spring Fling Towel Coaster Supplies Needed: 1 pieces 9x9 vinyl squares (available online and in some stores) 2 Sheets Fabri-Solvy (available online and in some stores) 1 Sheet Solvy WSS Thread Spray Adhesive White fabric Timtex, felt or heavy white fabric Iron Pressing Cloth 1. Hoop Fabri-Solvy, Fabric, WSS Solvy in that order. (Please do not omit the WSS solvy. It gives the design a crisp look.) 2. Sew out design up to the last two colors. 3. Stop. 4. Remove hoop from machine but DO NOT UNHOOP. 5. Center and place vinyl over design on top afixing with spray adhesive. 6. FLoat the Timtex or felt under the bottom afixing with spray adhesive. 6. Return hoop to machine and continue sewing out the next to the last color. 7. Remove hoop again (DO NOT UNHOOP) 8. Turn Hoop over. Trim only Timtex or felt away close to stitching but not through it. BE SURE NOT TO CUT INTO THE Fabri Solvy. 9. Turn Hoop back over to top and trim vinyl, WSS and fabric away close to stitching but not through it. BE SURE NOT TO CUT INTO THE Fabri Solvy. 9. Return hoop to machine and finish sewing last color. 10. Remove from hoop and trim design close to final stitch. 11. TO remove the excess Fabri Solvy use a warm water dampened sponge to run around the design. 12. Let finished coaster dry well if damp. 13. Place between the pressing cloth and gently press before use. ----------------------------------------------------------------------------------------------------------------------------- Spring Fling Towel Magnet Supplies Needed: 2 Sheets Fabri-Solvy (available online and in some stores) 1 Sheet Solvy WSS Thread Spray Adhesive White fabric Timtex, felt or heavy white fabric Iron Pressing Cloth Magnet and glue 1. Hoop Fabri-Solvy, Fabric, WSS Solvy in that order. (Please do not omit the WSS solvy. It gives the design a crisp look.) 2. Sew out design up to the last two colors. 3. Stop. 4. Remove hoop from machine but DO NOT UNHOOP. 5. FLoat the Timtex or felt under the bottom afixing with spray adhesive. 6. Return hoop to machine and continue sewing out the next to the last color. 7. Remove hoop again (DO NOT UNHOOP) 8. Turn Hoop over. Trim only Timtex or felt away close to stitching but not through it. BE SURE NOT TO CUT INTO THE Fabri Solvy. 9. Turn Hoop back over. On top trim WSS and fabric away close to stitching but not through it. BE SURE NOT TO CUT INTO THE Fabri Solvy. 9. Return hoop to machine and finish sewing last color. 10. Remove from hoop and trim design close to final stitch. 11. TO remove the excess Fabri Solvy use a warm water dampened sponge to run around the design. 12. Let finished magnet dry well if damp. 13. Place between the pressing cloth and gently press. 14. Attach a magnet to the back with glue. Allow to dry before use.